Static Route-configuration

 \[Command] show bgp peer-group \[Purpose] This command displays configured BGP peer-groups \[View] System view \[Use Cases] \[Command] show ip bgp summary \[{established|failed}] \[Purpose] View BGP neighbor information \[Parameter] established View the neighbors that have successfully established BGP neighbor relationships and interacted with routes failed View the neighbors whose BGP neighbor relationship establishment failed \[View] System view \[Use Cases] \[Command] show ip bgp neighbors \[Purpose] Display the details of BGP neighbors \[View] System view \[Use Cases] \[Command] show ip bgp \[Purpose] Display all route information received from BGP neighbors \[View] System view \[Use Cases] \[Command] show ip bgp statistics \[Purpose] Display BGP routing-related statistics \[View] System view \[Use Cases] \[Command] router bgp AS no router bgp AS \[Purpose] Enable a BGP protocol process with the specified AS number \[Parameter] AS AS number(1 4294967295) view specify view view name the name of view vrf specify VRF vrf name the name of VRF \[View] System configuration view \[Notes] When VRF VRF name is not specified, the BGP protocol process belongs to the default VRF.  \[Use Cases] \[Command] bgp router-id A.

BGP Configuration

 \[Command] show ip ospf \[vrf NAME |all] \[json] \[Purpose] Display OSPF details \[View] System view \[Use Cases] \[Command] show ip ospf \[vrf NAME |all] interface \[ethernet interface name |vlan vlan id |link-aggregation lag id ] \[Purpose] Show state and configuration of OSPF the specified interface, or all interfaces if no interface is given.  \[Parameter] interface name Ethernet interface name (0..

OSPF Configuration

 \[Command] show route-map WORD \[Purpose] Display data about each daemons knowledge of individual route-maps \[Parameter] WORD route-map name \[View] System view \[Use Cases] \[Command] clear route-map counters WORD \[Purpose] Clear counters that are being stored about the route-map utilization so that subsuquent show commands will indicate since the last clear \[Parameter] WORD route-map name \[View] System view \[Use Cases] \[Command] show ip prefix-list {detail|summary| NAME } \[Purpose] Display the IP prefix list \[View] System view \[Use Cases] \[Command] bgp large-community-list {standard|expanded} NAME {permit|deny} LARGE-COMMUNITY no bgp large-community-list {standard|expanded} NAME {permit|deny} LARGE-COMMUNITY \[Purpose] This command defines a new standard large-community-list \[Parameter] Standard Standard community list Expanded Expanded community list NAME Community list name LARGE-COMMUNITY large community in 'aa\ bb\ cc' format \[View] System configuration view \[Notes] When filtering BGP large community attributes, you can configure multiple filter criteria within the same entry.  The relationship between filter criteria is "AND," which means all filter criteria must be matched for the rule to be considered a match.

Route Map

 \[Command] show pbr interface interface-name \[Purpose] View the binding relationship between interfaces and policy routes \[View] System view \[Use Cases] \[Command] show pbr map map-name \[Purpose] Display the configured policy routes \[View] System view \[Use Cases] \[Command] show pbr nexthop-groups \[Purpose] Displays the next address group for the policy route \[View] System view \[Use Cases] \[Command] pbr-map name seq number \[Purpose] Create a policy route and enter the view \[Parameter] name Specify the policy name number Policy ID, value range 1-700, the lower the number, the higher the priority \[View] System configuration view \[Use Cases] \[Command] match { dst-ip ip-address|dst-port port|ip-protocol protocol|src-ip ip-address|src-port port } \[Purpose] Create match conditions for policy routing \[Parameter] dst-ip ip-address Match the destination IP address of the packet dst-port port Match the destination port of the packet ip-protocol protocol Match the protocol type of the packet src-ip ip-address Match the source IP address of the packet src-port port Match the source port of the packet \[View] Policy route view \[Use Cases] \[Command] set { nexthop ip-address|nexthop-group name } \[Purpose] Configure an action of redirecting packets to a next-hop IP address \[Parameter] nexthop ip-address Nexthop ip address nexthop-group name Nexthop group name \[View] Policy route view \[Notes] The redirect nexthop command allows user to specify a maximum of 4 next-hop IP addresses.  If multiple next-hop IP addresses are configured, the device redirects packets in active/standby mode.

Policy Route Configuration

 \[Command] show vrf brief \[Purpose] Display vrf-related configuration information \[View] System view \[Use Cases] \[Command] vrf vrfname \[Purpose] Add VRF \[Parameter] vrfname VRF name, length 1-11 \[View] System configuration view \[Use Cases] \[Command] ip route A. B.

MAP Configuration

IP Unicast Routing

delete-span-style

Routing & Gateway

Getting Started with VMware ESXi

Getting Started with Linux KVM

Preface

Applicable Hardware Models

VPP Router Overview of Router Functional Modules

First Use

System Configuration Guide

Interface Management Configuration Guide

PPPoE Interface Configuration Guide

MAC Configuration Guide

LAG Configuration Guide

VLAN Configuration Guide

MSTP Configuration Guide

QinQ Configuration Guide

MC-LAG Configuration Guide

MVRP Configuration Guide

DHCP Configuration Guide

NAT Configuration Guide

MAP Configuration Guide

BGP Configuration Guide

OSPF Configuration Guide

Policy Routing Configuration Guide

Security Configuration Guide

ACL Configuration Guide

QoS Configuration Guide

Network Monitoring Configuration Guide

Network Management Configuration Guide

User Access and Authentication Configuration Guide

Reliability Configuration Guide

TRACK and SLA Configuration Guide

VRRP Configuration Guide

IPSec Configuration Guide

WireGuard Configuration Guide

DNS Configuration Guide

Geosite/Geoip Configuration Guide

Reflect-acl Configuration Guide

Configuration Guide

Login System

Enter The Command Line Configuration Interface

Device Upgrade

System Boot Configuration

Basic Configuration

Device Status

Device Configuration

NTP Configuration

System Time Configuration

POE Configuration

Device Management

Interface Basic Configuration

Sub-interface Configuration

Loopback Interface Configuration

Port Group Configuration

Interface Bandwidth Utilization Alert

Interface Management

Link Aggregation Configuration

MC-LAG Configuration

LLDP Configuration

VLAN Configuration

MAC Configuration

Interface Isolation Group Configuration

STP Configuration

QinQ Configuration

MVRP Configuration

Ethernet Switching

IPv4 Configuration

ARP Configuration

ARP To Host Routing Configuration

DHCP Relay Configuration

DHCP Server Configuration

IPv6 Configuration

NAT Configuration

PPPoE Configuration

IP Service

9-1-acl-configuration

9-2-network-traffic-security-inspection

9-3-dhcp-snooping-configuration

ND Snooping Configuration

User Binding Rule Configuration

IPv6 RA Guard Configuration

IPSG Configuration

SAVI Configuration

ARP Detection Configuration

Security Configuration

Priority Map Configuration

Traffic Regulation

Queue Scheduling

Traffic Shaping

QoS Configuration

Mirror Configuration

SNMP Configuration

Syslog Configuration

IPFIX Configuration

Prometheus Exporter

Network Management And Monitoring

BFD Configuration

Monitor Link Configuration

VRRP Configuration

Reliability Configuration

Local User Configuration

AAA Configuration

License Configuration

User Access And Authentication

IPSec Configuration

DNS Configuration

WireGuard Configuration

Geosite/Geoip Configuration

Ucentral-client

Command Line Reference